google.com, pub-1613111081024165, DIRECT, f08c47fec0942fa0

Understanding the Solutions that Decorative Concrete can provide you.

Understanding the solutions that our products provide can be somewhat confusing because quiet frankly, there are just too many options and solutions. With that said, we will start by breaking down the solutions into two categories; Exterior and Interior…

 

Exterior:

– Splatter Texture Overlay: Applied approximately 1/16″ to 1/8″ thick to existing concrete to create a non-slip texture. Can be applied as plain gray or unlimited color and design choices. Patterns can replicate that of brick, stone, slate, tile, etc.

– Slate Trowel Overlay: Very similar to splatter texture overlay but typically a smoother finish.

– Concrete Staining: Transforms play gray concrete into a multitude of color options.

– Concrete Coloring: The concrete and be integrally colored before it is poured or it can be colored afterwards.

– Concrete Restoration: Repair unsightly spalling and pitting. Repair uneven or sunken surfaces.

Read the rest of this entry

A Few Important Concrete Cleaning Tips…

Concrete surfaces tend to accumulate dust very gradually and when it does, you realize how difficult it is to clean the exterior. This is precisely one of the reasons why periodic concrete cleaning helps in maintaining your home, driveway, and concrete patios to give it a yearlong spic and span look. High quality pressure washing is a key element of proper concrete cleaning. 

What Is Pressure Cleaning?

Pressure cleaning is a method of using high-pressure water to clean hard to remove the dirt, grime and grease from concrete surfaces. The system consists of a pump with a spray that creates high-pressure water with high velocity that enables cleaning of stains on concrete surfaces.

Points To Remember

* To start with, you will need a proper pressure washer, gloves, approved chemicals, eye protection equipment, water source, power source and accessories.

* Use a power washer with adequate pressure, preferably 3000 psi and with a flow rate of at least 4-5 gallons per minute.

New Video Added to Video Section…

Stamped Concrete or Troweled Concrete Overlay,, what’s the difference??

Our potential clients often ask us the differences between stamped overlays and troweled overlays There are significant differences that every homeowner should be aware of before making a decision about their concrete coating project.

Stamped concrete is concrete that is patterned and/or textured or embossed to resemble brick, slate, flagstone, stone, tile, wood, and various other patterns and textures. Stamped concrete is commonly used for patios, sidewalks, driveways, pool decks, and interior flooring. The ability of stamped concrete to resemble other building materials makes stamped concrete a less expensive alternative to using those other authentic materials such as stone, slate or brick.

There are three procedures used in stamped concrete which separate it from other concrete procedures; the addition of a base color, the addition of an accent color, and stamping a pattern into the concrete. These three procedures provide stamped concrete with a color and shape similar to the natural building material. It also is longer lasting than paved stone, and still resembles the look. One Drawback to Stamped Concrete as compared to Troweled on Systems,  it is more expensive to do just because it requires more material to be placed and can be mo re time consuming as well. So basically more material and labor are required.

A troweled coating is applied by troweling a cement mixture onto the top of existing concrete, usually at a thickness of approximately 1/8”.   The coloring on a troweled coating is put within the concrete while it’s being mixed.  The grout lines are taped  to resemble brick, slate, flagstone, stone, tile, then a tack coat is added over the tape to prevent bleeding of the colors (basically sealing in the grout coat so the top coat will not bleed into the grout lines. The Top coat is then applied in a rough texture to resemble rock or a smother texture to possibly to be more like Tile, or an knockdown finish may be desired, usually two to three coats of sealer is applied to Finish the Project.

 

For More information, questions or comments, please contact me here or visit my other website located here…

You can also become a Fan on Facebook ==>>

Follow us on Twitter ==>>

Watch our Video’s on Youtube ==>>


 Page 11 of 11  « First  ... « 7  8  9  10  11